About our boiler installation service

A new boiler is only as good as the system it is connected to. We look at the whole system first, then fit the boiler that suits it.

QPS installs gas boilers across Winchester, Eastleigh and the rest of Hampshire, from like-for-like swaps to full relocations with a new flue and pipework. Every installation is carried out by Gas Safe registered engineers and starts with a survey of the property, not a glance at the model number on the old boiler.

Much of our work is in larger homes and full renovations, where the boiler is one part of a designed system with a cylinder, zoned heating and sometimes two boilers. That is why we size boilers from a heat loss calculation, and why our system design work and boiler installations usually go together. You can see three recent Winchester examples, including two-boiler, five-bathroom houses, on our refurbishment projects page.

Vaillant boiler and Stelflow hot water cylinder in a plant room, with soldered copper pipework, motorised zone valves and a circulating pump on a dark painted brick wall

Our boiler installation service

Survey & Quote

We look at the property, the existing system and how you use hot water, then give you a clear, detailed quote.

Heat Loss & Sizing

The new boiler is sized from a heat loss calculation, not from the output of the one coming out.

Supply & Installation

We supply the boiler and materials, remove the old unit and install the new one in soldered copper.

System Clean & Protection

Every new boiler goes onto a cleaned system. We cold flush the radiators and run a cleaning chemical through for an hour or two, then drain, refill with inhibitor and fit a magnetic filter.

Gas Safe Commissioning

All gas work is carried out and certified by Gas Safe registered engineers, then fully commissioned and tested.

Warranty Registration

As Vaillant approved installers, most of the boilers we fit are Vaillant, with a 10-year parts and labour warranty that we register for you.

Hard water and your new boiler

Winchester and much of Hampshire sit on chalk, and the water here is hard. When hard water is heated it leaves limescale behind, and the first place it collects is inside the boiler: on the main heat exchanger and, in a combi, on the plate heat exchanger that makes your hot water.

Scale insulates whatever it coats, so the boiler works harder to deliver the same heat. Left alone it brings kettling noises, weaker hot water and, in time, early failure of parts. Combis feel it first, because every hot tap you run sends fresh hard water through the boiler.

So we talk about water treatment on every installation. Every combi we fit gets a scale reducer on the cold main as standard, to protect the boiler itself. For homes with two or more bathrooms we also recommend a water softener, which treats the whole house, protecting the boiler, cylinder, showers and taps. That is why a softener appears in so many of our plant room photos.

Wall-hung Vaillant ecoTEC plus boiler in a historic roof space, with insulated and labelled pipework below and a water softener on a stand beside it

Combi, system or regular?

The right boiler depends on the house, how many bathrooms you have and how you use hot water.

Combi Boiler

Heats water on demand, with no cylinder or loft tanks. Ideal for smaller homes with one bathroom.

System Boiler & Cylinder

Heats a stored cylinder of hot water at mains pressure. The better choice for two or more bathrooms, because several showers can run together without the flow dropping.

Regular Boiler

Works with a cylinder and tanks in the loft. Sometimes right for older properties, though a replacement is often the moment to convert to a sealed system.

Why Bathrooms Matter

A combi splits its output between every open hot tap. One shower is fine. Two at once on a busy morning is where combis disappoint, and where a cylinder earns its space.

Sized on Heat Loss

Copying the old boiler's output is how homes end up with an oversized boiler that short-cycles, wasting gas and wearing parts. We calculate heat loss room by room instead.

Radiators & Underfloor

A modern boiler runs most efficiently at lower temperatures, so the emitters matter too. We look at your radiators and underfloor heating as part of the same job.

What a new boiler costs

Guide prices for the most common boiler installations. Every house is different, so treat these as a starting point. We survey first, then give you a detailed quote for your home.

Combi

Like-for-like combi swap

From£2,500+ VAT

Replacing an existing combi in the same position. Most come in at £2,500 to £3,000.

Conversion

Regular system to combi

Around£5,000+ VAT

Moving from a regular boiler with a cylinder and loft tanks to a combi.

Cylinder

System boiler & unvented cylinder

From£5,000+ VAT

Typically £5,000 to £7,000, depending on where the existing boiler and cylinder are.

Included with every new boiler

A system clean, magnetic filter and inhibitor come with every installation, and every combi gets a scale reducer on the cold main. All prices are plus VAT, so there are no surprises at the end.

What can change the price

Moving the Boiler

Moving the boiler to another room, the loft or a garage means new gas, water and heating pipework. How far it moves and whether the services are nearby can change the price a lot, so we price relocations after the survey.

Existing Boiler & Cylinder

For a system boiler and new cylinder, where the existing boiler and cylinder sit is the main thing that decides where in the £5,000 to £7,000 range a job lands.

Flue Route

If the existing flue position still meets current regulations it can often be reused. A new route through a wall or roof adds materials and time, and is priced for each job.

Condensate Routing

Every condensing boiler needs a condensate drain. Where it cannot run to a drain by gravity, we fit a condensate pump, which adds around £150 to £200 + VAT.

Gas Supply Pipe Size

A new boiler can need a larger gas supply than the old one did. If the pipe from the meter is undersized it has to be upgraded, and the cost depends on the length of the run and the work involved.

Water Treatment

Every combi gets a scale reducer as standard. For homes with two or more bathrooms we recommend a water softener as well, at around £1,500 + VAT supplied and fitted.

What our customers say

"Joe and Sam were brilliant. They installed a new boiler for us in a different location to the previous one. Did it in two days and took away all the old parts including the big tank. Arranged for electricians and roofers to do their bit so we had nothing to worry about and left the place tidy after."

Mollie PellattBoiler installation & relocation

"Joe installed a new boiler and water tank as well as new radiators. He did a great job - started and finished when he said he would, neat and tidy ... excellent plumbing work, Joe is a perfectionist!"

Joe ThomsonBoiler, water tank & radiator installation

"Joe recently came to fix my leaking boiler, not an easy fix but you wouldn't even know he'd worked on it, workmanship was second to none and not had a single problem since."

Keeley FitzgeraldBoiler repair

"Workmanship was top quality always clean and tidy, and very helpful with any queries I had throughout the job. Would highly recommend and will be using QPS again in the future."

Common questions

A like-for-like combi swap starts from £2,500 + VAT, and most come in at £2,500 to £3,000. Converting a regular system to a combi is around £5,000 + VAT, and a system boiler with a new unvented cylinder is typically £5,000 to £7,000 + VAT. Every house is different, so we survey first and then give you a detailed quote.

No. All our prices are plus VAT, and we show them that way so there are no surprises at the end.

With one bathroom, a combi is usually the simpler choice. With two or more bathrooms, or showers that run at the same time, a system boiler with an unvented cylinder will serve you better.

That comes from a room by room heat loss calculation, not from the output of your old boiler. An oversized boiler short-cycles, wasting gas and wearing parts. For a combi, the hot water flow you need also affects the size.

It can. Hampshire water is hard, and limescale builds up on the heat exchanger, reducing efficiency and shortening its life. A scale reducer or softener fitted with the new boiler protects it from the start.

Every new boiler gets a magnetic system filter and inhibitor as standard, and every combi gets a scale reducer on the cold main. We recommend a water softener for homes with two or more bathrooms, at around £1,500 + VAT supplied and fitted.

Every new boiler we fit goes onto a cleaned system, and the clean is included as standard. We cold flush the radiators, then run a cleaning chemical through the system for an hour or two before draining it and refilling with inhibitor.

A straightforward like-for-like boiler replacement typically takes one day. If we are relocating the boiler or making changes to the pipework, it may take two days. We will confirm the timeline before starting.

Yes. We regularly move boilers to other rooms, the loft or a garage. The cost depends on how far it moves and whether the gas, water and drainage are close to the new position, which can make a big difference, so we price relocations after the survey.

It depends on how well it was installed, the water and system it sits on, and whether it is serviced every year. A correctly sized boiler on a clean, treated system has the best chance of a long life.

We mainly fit Vaillant boilers, which come with a 10-year parts and labour warranty. We register the warranty for you once the boiler is installed.

We remove and dispose of your old boiler and any redundant parts as part of the installation. You do not need to arrange anything separately.

Need a new boiler?

Tell us about your home and your current system, and we will arrange a survey and a clear, no-obligation quote. View our pricing →